Agusta-Bell 206B RC Helicopter in Scale 1:5.7 of the Greek Army Aviation




Introduction

I have started this blog as an english-text alternative to a thread that I have opened in modelclub.gr (modelclub forum in greek) regarding my project to build an RC scale model of an Agusta-Bell 206B Jet Ranger II of the Hellenic Army (see unofficial site).


Now a few words about the project itself. The model is based on the fuselage provided by Vario (model 1004) in scale 1:5.7. There are very little differences between a Jet Ranger III (model kit) and an Agusta-Bell AB-206B Jet Ranger II that I needed for the project, so I decided to get the kit from Vario. The kit has been bought from one of the best specialists and professionals in the field, Mr Thomas Baumann who has helped me with making my choice of the model and its accessories (Helikopter Baumann). Thanks Thomas! I would also like to thank the team of eflight for their professional support not only for this construction but for all my RC models and accessories. In addition, I would like to thank the team from Innoflyer and especially Mr. Christophe Raible for the help with the lighting system and for letting me test a new CPL model before its official launch. I would like to add here the biwix.com RC helicopter store and Johnny Trolliet at my hometown Renens for his exceptional service, availability and prices!

The particularity of this project is that the mechanism that I fit in the fuselage is not the one from Vario but a modified Align T-Rex 700E (Align RC Helicopters). I will give here details on the way that this is done with diagrams, photos, tips and tricks. This will cover the first part. The flight tests of the modified T-REX 700E have been conducted at the RC model field in Dizy, Switzerland that belongs to the Dizy RC Modelling Group (GAM Dizy). Big THANKS to all the members of the Club for the great friendliness since the first day I started there and for their help with advice and tips!

The second part will be dedicated to the scale model itself. Some photos of the Greek AB-206B can be found on the internet but they do not cover all the details. More photos of the aircraft with the Greek colors may be requested in the forum of modelclub.gr where I have gotten most of them thanks to the team spirit and great friendliness of the members (THANKS^1000 dsamba!!!). In order to complete the photographic part of the project I managed to get my own photos of a Jet Ranger III. This has been made possible thanks to the courtesy of the people from Heli-Lausanne (Heli-Lausanne) who have immediately accepted my request to get there and take as many photos as I needed. A big THANKS to them too!!!
At the last phase of construction, I have got invaluable help for the dimensions of the AB-206B landing gear from Iraklis Karailidis. Many-many thanks to you Iraklis!

So after this short introduction I will start publishing the steps I have already taken and will take during this quite challenging project (at least for me, it is my first scale RC helicopter).

I hope that you will find this blog helpful if you have a similar (or the same) project as mine and you will enjoy it as much as I do!

Welcome!
Hellenicopter

29/11/2013

I continue with some details already published on modelclub.gr.

Here are some photos showing the tilt of the main shaft as well as the point of exit from the fuselage. They look quite OK with the scale (I remind you that the shaft is not the original shaft from Align but a customized shaft from Vario - see pdf).



One more photo showing the position of the front part of the skids legs with respect to the fuselage.



Another photo from inside with the Trex mechanics mounted.



Other stuff from the same site: the engine cowl with the openings for cooling. The round opening on the side has been made with a 0.8mm drill and a printed pattern on auto-adhesive sheet. I realized later that the pattern is not correct as it is rectangular instead of rhombic. I will have to correct it. There are also photos showing the real opening and the dimensions of this round opening. On the top there are two round-shaped openings. The estimated size is given. The openings are cut to the proper size for the scale but they are not very well positioned as I found out later and I will also have to correct that.





07/11/2013

A few days ago I have published a pdf regarding the basic modifications I have made to the mechanics of the Trex 700E in order to install it in the Vario Jet Ranger fuselage. Here I elaborate a bit some steps that presented some difficulty.

The Tail Boom

In general, the Trex mechanics fit surprisingly well into the Vario fuselage. The main difficulty is the tail boom and the hub. Initially, I have tried to use the upgrade available by Align to convert a Trex 700E to an 800. Unfortunately, this doesn't work, the boom and the shaft are 3-4cm too short. I had to buy in addition a Trex-800 tail shaft. It is difficult to find aluminum tubes in the raw-material market with the right cross-section dimensions so you have to put together the tail boom from the upgrade with an extension that is cut off from a second tube (available from the original Trex-700E kit). I have tried to use a CF tube but it was not easy because the cross-section was not wide enough. I think that Align has chosen on purpose to use tubes with those non-standard cross-section dimensions in order to be forced to buy their tubes...

In my case, I have decided to merge the two boom parts towards the frame side and not the hub side. This is done because at the frame side it is much easier to put them together in a reliable way. A 20mm aluminum tube is used to merge the two boom parts from the inside without creating any problems to the shaft. The small part has been glued with epoxy glue to this tube (with Devcon 30min, still the best out there, much better than the 30min Zap epoxy) and the long full-length boom has been screwed on it with two short M4 screws (see picture in pdf). The short boom piece resides safely in the plastic gear box at the back of the Trex's CF frame. The long boom part is partly inside the same gear box.


The boom parts have to be assembled and secured before installing the mechanics at their final position.

Securing the Lynx rods to the boom before final installation of the mechanics in the fuselage.

Tightening the screws at the rear of the plastic gear box.
In brief, this solution works fine but I would prefer to have a full length tube instead. Unfortunately, although the Trex-800 boom has the right length, it is too large (25mm cross-section) to go through the fuselage's tail and doesn't do the job (I would have to change the plastic gear box and the tail hub too).  In addition, the Lynx Heli Innovations tail boom mounting rods (cut to the right length) have helped a lot to add stability. Those rods come already glued and screwed to their aluminum anchors and it is difficult to unglue them in order to adjust their length (you need a hot-air pistol at around 200 degrees Celsius and a lot of patience!).


Gluing back together the aluminum anchors to the tail boom mounting rods.

 

Connecting the boom to the fuselage

The connection of the GF (glass fiber) tail boom to the fuselage has been modified in order to be able to pass through it the Trex's tail tube. Two multi-layer 5mm-thick plywood plates have been glued on each side (fuselage sied and tail side). On the tail side two M5 drive-in nuts have been used for screwing the two parts tightly together (see pictures below).



The Tail Hub


The second "headache" has been the mounting of the tail hub. The tail of the fuselage already provides a quite big opening and it is almost perfect for the installation of the Trex-700E hub. Well, almost... I had to cut out a small opening for the hub's tightening screws as you can see in the picture below. This is a necessary "evil" as there is no other way to fit the hub. In the final assembly the metallic part of the hub barely overhangs out of the fuselage. In the real helicopter this part of the tail is covered by a canopy from above that is held with numerous screws on the body of the tail (see pictures below). So there is still place for hiding this with such a canopy made of glass-fiber or carbon fiber and held in place with screws as well (see photo below of a CF cover I made).
Picture showing the opening in the GF part of the tail to accommodate the tail hub.

Tail cover made of CF and epoxy. The lighter the better in order to avoid adding too much weight on the tail.


Finally, in order to better integrate the hub in the fuselage an aluminum plate has been made (1.5mm-thick) in order to screw the hub on the fuselage (see following pictures).


In order to avoid bad surprises and to reinforce the fuselage around the hub I laminated the internal surface of the fuselage with one 3K carbon-fiber sheet. In this way there is much less risk for the screws holding the plate and the hub to crack the fuselage and finally break it due to vibrations.


21/10/2013

First hover of the Vario Jet Ranger with the TREX-700E mechanics


Back again with the video of the first hover of the Jet Ranger model before starting the coverage of the whole construction. Enjoy!

Here are some photos of the helicopter and details on the mounting of the TRex mechanics in the Vario (model 1004) fuselage.


30/09/2013

Agusta-Bell 206B RC Helicopter in Scale 1:5.7 of the Greek Army Aviation


Introduction 


I start this blog as an english-text alternative to a thread that I have opened in modelclub.gr (modelclub forum in greek) regarding my project to build an RC scale model of an Agusta-Bell 206B Jet Ranger II of the Greek Army (see unofficial site). The model is based on the fuselage provided by Vario (model 1004) in scale 1:5.7. There are very little differences between a Jet Ranger III (model kit) and a Jet Ranger II that I needed for the project, so I decided to get the kit from Vario. The kit has been bought from one of the best specialists and professionals in the field, Mr Thomas Baumann who has helped me with making my choice of the model and its accessories (Helikopter Baumann). Thanks Thomas!

The particularity of this project is that the mechanism that I fit in the fuselage is not the one from Vario but a modified Align T-Rex 700E (Align RC Helicopters). I will give here details on the way that this is done with diagrams, photos, tips and tricks. This will cover the first part. The flight tests of the modified T-REX 700E have been conducted at the RC model field in Dizy, Switzerland that belongs to the Dizy RC Modelling Group (GAM Dizy). Big THANKS to all the members of the Club for the great friendliness since the first day I started there and for their help with advice and tips!

The second part will be dedicated to the scale model itself. Some photos of the Greek AB-206B can be found on the internet but they do not cover all the details. More photos of the aircraft with the Greek colors may be requested in the forum of modelclub.gr where I have gotten most of them thanks to the team spirit and great friendliness of the members (THANKS^1000 dsamba!!!). In order to complete the photographic part of the project I managed to get my own photos of a Jet Ranger III. This has been made possible thanks to the courtesy of the people from Heli-Lausanne (Heli-Lausanne) who have immediately accepted my request to get there and take as many photos as I needed. A big THANKS to them too!!!

So after this short introduction I will start publishing the steps I have already taken and will take during this quite challenging project (at least for me, it is my first scale RC helicopter).

I hope that you will find this blog helpful if you have a similar (or the same) project as mine and you will enjoy it as much as I do!

Welcome!